Skakelaar: Verskil tussen weergawes

Content deleted Content added
RAM (besprekings | bydraes)
No edit summary
Lyn 33:
===Maak-voor-breek, breek-voor-maak===
In 'n skakelaar met multiskakelings is daar twee moontlike oorgangstoestande soos daar van die een posisie na 'n ander beweeg word. In sommige skakelaarontwerpe word die nuwe kontakte verbind voordat die ou verbindings verbreek word. Dit staan bekend as 'n maak-voor-breek tipe skakelaar en verseker dat die bewegende kontak nooit 'n oop stroombaan veroorsaak nie (word ook soms na verwys as 'n kortsluitskakelaar). Die alternatief is 'n breek-voor-maak tipe skakelaar waar die ou kontakverbinding eers verbreek word voordat die nuwe een verbind word. Dit verseker dat daar nooit 'n kortsluiting tussen die kontakte plaasvind nie. Beide soorte ontwerpe word algemeen gebruik vir verskillende toepassings.
 
==Verwysings==
{{verwysings}}
 
==Sydige skakelaars==
Line 61 ⟶ 58:
===Twee liggings===
[[Beeld:Tweerigtingskakelaar.PNG|right|frame|1. Eerste Metode<br>2. Tweede metode<br>3. Benoeming van terminale]]
Die aanskakel van 'n lading (soos 'n lig aan beide kante van 'n stel trappe) vereis twee EPDS skakelaars. Daar is twee basiese metodes om dit reg te kry.
 
Met die eerste metode word die kragbron na die gemene terminaal van een van die skakelaars gekoppel; hierdie skakelaars word dan deur L1 en L2 terminale verbind en dan word die kragvoer na die lig vanaf die gemene terminaal van die tweede skakelaar afgevoer. A word aan B of C gekoppel of C en D word aan B of C gekoppel; die lig sal dan brand as A aan D gekoppel word, d.w.s. As A en D beide aan B of beide aan C gekoppel word.
 
<!-- Moet nog vertaal word
 
===Two locations===
[[Image:Twowayswitching.PNG|right|frame|1. First method<br>2. Second method<br>3. Labelling of switch terminals]]
Switching a load on or off from two locations (for instance, turning a light on or off from either end of a flight of stairs) requires two SPDT switches. There are two basic methods of wiring to achieve this.
 
In the first method, mains is fed into the common terminal of one of the switches; the switches are then connected through the L1 and L2 terminals (swapping the L1 and L2 terminals will just make the switches work the other way round), and finally a feed to the light is taken from the common of the second switch. A connects to B or C, D connects to B or C; the light is on if A connects to D, i.e. if A and D both connect to B or both connect to C.
 
The second method is to join the three terminals of one switch to the corresponding terminals on the other switch and take the incoming supply and the wire out to the light to the L1 and L2 terminals. Through one switch A connects to B or C, through the other also to B or C; the light is on if B connects to C, i.e. if A connects to B with one switch and to C with the other.
Line 186 ⟶ 180:
*[http://www.ikalogic.com/debouncing.php Tutorial about switch de-bouncing] Analog and digital debouncing are discussed with schematics and example source codes
-->
 
==Verwysings==
{{verwysings}}
 
[[Kategorie:Elektrisiteit]]
[[Kategorie:Elektronika]]